TC ENCORE?

Talk Anything related to Muzzleloader
UtahRob
4 point
4 point
Posts: 526
Joined: Mon Mar 20, 2006 12:22 pm

Post by UtahRob » Wed Oct 03, 2007 2:02 pm

What primers are you Encore users using??

Anyone using the breach plug with the 22 hornet conversion ???
I understand there is no blow by and you get better groups with it !!

Image

TCsmokepole
Spike
Spike
Posts: 52
Joined: Wed Sep 12, 2007 8:19 pm
Location: Logan UT

Post by TCsmokepole » Thu Oct 04, 2007 10:51 pm

Winchester 209 Primers for Shotshells BOX says W209 lotta bang for not much buck run about $3.50 per box 100 primers. :thumb
One shot is all I Got.
Better make it count, or reload fast.

UtahRob
4 point
4 point
Posts: 526
Joined: Mon Mar 20, 2006 12:22 pm

Post by UtahRob » Sat Oct 06, 2007 7:29 pm

I got my Encore today !!!


Can't wait to shoot it . I am surprised how light it is compared to my Tradition pursuit pro .

TCsmokepole
Spike
Spike
Posts: 52
Joined: Wed Sep 12, 2007 8:19 pm
Location: Logan UT

Post by TCsmokepole » Sat Oct 06, 2007 10:54 pm

COOL! enjoy the new toy I've sure enjoyed mine. salxxute seem to be dead on right out of the box. :thumb
One shot is all I Got.
Better make it count, or reload fast.

UtahRob
4 point
4 point
Posts: 526
Joined: Mon Mar 20, 2006 12:22 pm

Post by UtahRob » Thu Oct 18, 2007 5:30 pm

Anyone put any after market stuff on their Encores ??

TCsmokepole
Spike
Spike
Posts: 52
Joined: Wed Sep 12, 2007 8:19 pm
Location: Logan UT

Post by TCsmokepole » Fri Oct 19, 2007 11:36 am

I put a screw in Limbsaver pad, :thumb
E-Z Tip Extractor :thumb
T-handle Power rod. :thumb

Almost a TC Pro hunter
One shot is all I Got.
Better make it count, or reload fast.

UtahRob
4 point
4 point
Posts: 526
Joined: Mon Mar 20, 2006 12:22 pm

Post by UtahRob » Thu Oct 25, 2007 3:06 pm

I just got the e-z tip and the t- handle in the mail from cabela's yesterday .:thumb

I did replace the hinge pin with the two peace one , way easier to remove and will not move.

UtahRob
4 point
4 point
Posts: 526
Joined: Mon Mar 20, 2006 12:22 pm

Post by UtahRob » Tue Oct 30, 2007 1:00 pm

I shot my Encore yesterday and my shots were all over the place . So i inspected my gun and noticed the rear stock was very ,very LOOSE. I could not even get a 10' group . So i went home tightened the stock and went out this morning and shot 6 shots at 50 yards . Got rained out and so will go again this afternoon and raise my group up about 2 inches . I am very impressed with my Encore. :thumb I am shooting the same loads that i used in my Traditions , 100 grains of loose ffg , 300 grain XTP HP and Klean bore primers . I used Windex on the two wet patches ( both sides ) and then used a dry patch ( both sides ) after each shot.

Image
Last edited by UtahRob on Thu Nov 08, 2007 2:14 am, edited 2 times in total.

TCsmokepole
Spike
Spike
Posts: 52
Joined: Wed Sep 12, 2007 8:19 pm
Location: Logan UT

Post by TCsmokepole » Fri Nov 02, 2007 10:03 am

They work well if you see one in range he should be a dead one :thumb
One shot is all I Got.
Better make it count, or reload fast.

Post Reply
cron